Delta PT (PT Plaster Lath and PT Slimline) Cavity Drain Membrane

Delta PT is a High Density Polyethylene (HDPE) cavity drain membrane.  Delta PT has been designed to incorporate a plastic mesh which is welded to the surface of this dimpled sheeting membrane.  Suitable as an impermeable damp proofing base for plaster or shotcrete (and as a water control and drainage membrane) in tunnel construction or for remedial damp proofing and waterproofing of existing basements internally.

_x000D_\n

_x000D_\n
• Type C Drained Protection in accordance with BS 8102:2009
_x000D_\n
• BBA Approved
_x000D_\n
• A reversible system, which will minimize damage to historical or heritage structures
_x000D_\n
• Virgin high density polyethylene studded/moulded sheet (HDPE)
_x000D_\n
• An effective barrier to the transmission of salts, liquid water and water vapour
_x000D_\n
• Available in 2 stud heights
_x000D_\n
• Resistant to chemicals, root penetration, rot proof, neutral towards drinking water
_x000D_\n
• Suitable for Flood Resilience
_x000D_\n
• Inert and compatible with all building materials
_x000D_\n
• Meets the requirement for a radon barrier
_x000D_\n
• Neutral towards drinking water
_x000D_\n

_x000D_\n

_x000D_\n

Specification

_x000D_\nNBS Specification J40 (Clause 290) Flexible Sheet Tanking/Damp Proofing.  BS 8102:2009 Type C Drained Protection._x000D_\n

Available in 3 stud heights: 8mm, 7mm and 4mm.

_x000D_\nDepending on the application required and the site conditions, the membrane may be used as:_x000D_\n

_x000D_\n
• a dry lining for walls, ventilated into the room via aeration slots at the top and bottom of the wall or via passive air vents, where access through an external wall is available
_x000D_\n
• a sealed system covering wall, floor and ceiling with provision made for disposing of water build-up behind the membrane via a sump and pump.
_x000D_\n

_x000D_\nIt can support plastering, rendering or a dry lining fixed by plaster dabs (where appropriate) in the following situations:_x000D_\n

_x000D_\n
• on damp walls in underground situations subject to high groundwater levels, and perennial moisture
_x000D_\n
• on vaulted ceilings of archways or cellars subject to water ingress
_x000D_\n
• in conjunction with a remedial dpc system where the walls have a high salt content, and/or it is necessary to complete the installation immediately without allowing a period for initial drying
_x000D_\n
• over walls which have a friable or painted surface, are contaminated with oil or mould, or have a high salt content
_x000D_\n
• as a waterproofing membrane in areas subject to vibration.
_x000D_\n

_x000D_\n

Ancillary Products

_x000D_\n _x000D_\n_x000D_\nOur ranges of ancillary products work as the perfect compliment the Delta MS 20 Cavity Drain System, allowing for application on different substrates and surfaces both sealing and dealing with protrusions and condensation. We recommend:_x000D_\n

_x000D_\n
• PT Plugs
_x000D_\n
• PT Plugs (with Grommets)
_x000D_\n
• FlexiDri Plus Plugs
_x000D_\n
• Delta Rope
_x000D_\n
• Delta Tape
_x000D_\n
• Delta Fleece Tape
_x000D_\n
• Delta PT Profile Ventilation Strip
_x000D_\n
• Delta Corner Strip
_x000D_\n
• Delta Mastic
_x000D_\n
• Delta Than
_x000D_\n
• Koster Polysil TG 500 – Anti-Lime Coating/Surface Primer
_x000D_\n